SSOUNDS · SS-D34X
SSOUNDS D34X
출시 예정. 4채널 네트워크 DSP 앰프, 8Ω에서 4 × 3,000W, Dante, AES3 및 아날로그 입력.
AES3DSPamplifierFIRsnettouringinstallD34X는 SSOUNDS D시리즈를 D24X 이상으로 확장하여 가장 큰 XTO 및 LS 배포를 지원합니다. 4개의 Class-D 채널은 8Ω에서 각각 3,000W를 제공하며, FIR 및 IIR 처리, SSOUNDS 라우드스피커 및 카디오이드 프리셋, Dante 오디오 및 제어, AES3 및 아날로그 입력, SSOUNDS 네트워크 매니저를 통한 SNet 원격 제어 및 모니터링을 지원합니다. 관심 등록 또는 시스템 계획을 위해 문의해 주세요.
Part of the XTO System
One per 14P. Four channels driving the four sections of a single cabinet, nothing paralleled.
Key features
- Coming soon, shipping date on request
- 4 × 3,000 W into 8 Ω, 4 × 6,000 W into 4 Ω, 24,000 W total
- 0.466 ms latency, analog input to loudspeaker output
- SSOUNDS DSP, 32-bit floating point at 96 kHz
- PhaseTrue linear-phase FIR crossovers, with IIR shelving, parametric and notch
- DynaControl peak, thermal and excursion limiting, plus cardioid subwoofer presets
- Dante audio, AES3 and analog inputs, SNet control
- 16-band input and 16-band output EQ, parametric, notch and shelving
- Variable-speed cooling under continuous temperature monitoring, with GPIO
Specifications
Engineering data. The conditions each figure is specified under are stated below the table.
General
- Type
- 4-channel DSP power amplifier, networked
- Protection
- Over-current · thermal · DC · short-circuit
- Cooling
- Forced-air front-to-rear, variable-speed fans under continuous temperature monitoring
- Certifications
- CE · UKCA · TÜV (rack mounting) · FCC · cULus · EAC · RoHS
Electrical
- Channels
- 4 × Class-D
- Power @ 8 Ω
- 4 × 3,000 W
- Power @ 4 Ω
- 4 × 6,000 W
- Bridged @ 8 Ω
- 2 × 12,000 W
- Minimum load impedance1
- 2 Ω (all channels driven)
- Total output
- 24,000 W
- Mains
- 200–240 V switch-mode with PFC
Processing
- Presets and delay
- SSOUNDS loudspeaker presets, cardioid subwoofer modes, per-channel delay
- Converters
- 32-bit AD / DA at 96 kHz
- DSP platform
- SSOUNDS DSP, 32-bit floating point with 40-bit extended precision
- Latency
- 0.466 ms, analog input to loudspeaker output
- Crossover filters
- PhaseTrue linear-phase FIR, with IIR shelving, parametric and notch sections
- Limiting
- DynaControl peak, thermal and excursion limiting, per channel
- Equalisation
- 16 bands on the input and 16 bands on the output, parametric, notch and shelving
- Load monitoring
- Per-channel load impedance monitoring with fault reporting over SNet
- Maximum delay
- 1,000 ms per channel
Connections
- Network
- Dante audio network + control, 2 × RJ45 (primary / secondary, front panel)
- Control
- SNet remote control and monitoring (SSOUNDS Network Manager)
- Inputs / outputs
- 4 × XLR analog / AES3 · Dante · 4 × NL4 speakON out
- GPIO
- General-purpose I/O for external monitoring and control
- Input sensitivity
- 0 dBu / 6 dBu selectable
Performance
- Frequency response
- 20 Hz – 20 kHz (±0.5 dB)
- Dynamic range
- 112 dB
- THD+N
- < 0.02% @ 1 kHz
- S/N ratio
- > 112 dB (A-weighted)
- Damping factor
- > 500 @ 8 Ω
- Efficiency
- > 90%
Physical
- Format
- 19″ 2U rack
- Net weight2
- 14 kg / 31 lb
Environment
- Operating temperature
- −10 °C to +40 °C continuous, +50 °C short term
- Storage temperature
- −20 °C to +70 °C
- Humidity
- < 70% relative humidity, non-condensing
Measurement conditions
- Nominal impedance is the manufacturer's rating for amplifier load calculation; minimum impedance across the operating band may be lower.
- Net weight excludes packaging, flight case, accessories and optional rigging hardware.
- All figures are typical values for production units specified under the conditions above. Individual units may vary within published tolerances.
Downloads
Product documentation, free to open. No registration, no form. The data sheet is a PDF rendered from the page below it; the manual is a print page, so use your browser to print it or save it as PDF.
- Technical data sheetFull specification set with the measurement conditions for each figure, modelled response curves, safety notices and warranty terms.PDF · SS-DS-D34X-EN-A4 · Rev. 2608 · Issued 14 Aug 2026
- Technical data sheet, in your browserThe same document as a page, if you would rather read it here or print it yourself.HTML print view · SS-DS-D34X-EN-A4 · Rev. 2608 · Issued 14 Aug 2026
- Architectural and engineering specificationThe “shall be” paragraph for tender documents and bills of quantities, written from this product’s own specification rows. Section of the data sheet.HTML section · SS-DS-D34X-EN-A4
- User manualUnpacking, connection, installation, operating limits, maintenance schedule and troubleshooting for this model.HTML print view · SS-UM-D34X-EN-A4 · Rev. 2608 · Issued 14 Aug 2026
Loudspeaker data files for prediction software (GLL and CLF for EASE), 2D and 3D drawings and certification documents are issued on request. Email support@s-soundspro.com and we will send the current release for this model.
More from the SSOUNDS amplifier range
SSOUNDS
SSOUNDS A34X
Coming soon. 4-channel Class-D amplifier, 4 × 3,000 W at 8 Ω, analog input, no onboard DSP.
SSOUNDS
SSOUNDS D24X
High-power 4-channel DSP amplifier, subwoofer-grade output with full FIR processing.
SSOUNDS
SSOUNDS D14X
4-channel DSP amplifier with FIR, line-array power plus full system processing and presets.
SSOUNDS
SSOUNDS A24X
High-power 4-channel subwoofer amplifier, 4 × 4,400 W @ 4 Ω for XTO sub arrays.
SSOUNDS
SSOUNDS A14X
4-channel touring amplifier for line arrays, 4 × 2,000 W @ 4 Ω, analog input.