1 / 6SSOUNDS · SS-XTO-46
SSOUNDS XTO 4.6
عنصر عمود في نظام XTO، مصفوفة خطية سلبية، 4 × 6.5 بوصة محركات، 65 هرتز – 20 كيلو هرتز وذروة 134 ديسيبل في عمود يحافظ على وضوح الرؤية.
إن XTO 4.6 هو عنصر العمود في نظام XTO، حيث يجمع سلوك المصفوفة الخطية الحقيقي في هيكل نحيف: أربعة محركات مقاس 6.5 بوصة ومحرك ضغط بملف صوتي مقاس 2 بوصة يوفران 65 هرتز – 20 كيلو هرتز وذروة 134 ديسيبل من صندوق بعرض 200 مم فقط. يمكنك توصيل الوحدات عمودياً للحصول على مصفوفات أطول ومدى أبعد، أو تعليقها أو تركيبها على الحائط باستخدام نظام حوامل XTO، أو تركيب عمود واحد على قاعدة مضخم صوت. إنها الوحدة التي يجب تحديدها عندما يجب سماع النظام وليس رؤيته: الكنائس والمسارح وقاعات المؤتمرات وأنظمة الصوت المرئي المؤسسية الفاخرة.
Part of the XTO System
Passive column element where the hang has to disappear into the room.
XTO stands for Xtended Touring Output. The large-format touring platform: the elements built for the longest throws and the highest output in the range, rigged and amplified as one system.
Key features
- 4 × 6.5″ LF drivers with a 2″ voice-coil compression driver in a 200 mm-wide column
- 65 Hz – 20 kHz with 134 dB peak SPL
- 100° horizontal by 25° vertical coverage per module
- Modules couple vertically for longer throw and tighter vertical control
- Fly, wall-mount or pole-mount from a single bracket system
- Sightline-friendly profile for heritage rooms and architectural installs
Specifications
Engineering data. The conditions each figure is specified under are stated below the table.
General
- Type
- Passive column line-array element
- Certifications
- CE · TÜV (rigging system) · EAC · WEEE
Components
- Drivers
- 4 × 6.5″ cone drivers · 8 Ω + 1 × 2″ coil HF compression driver
Acoustic
Connections
- Connectors
- 2 × NL4 speakON (in / link)
- Pin map
- 1+/1− full range · 2+/2− not linked
Rigging
- Mounting
- Inter-module coupling · fly / wall bracket · 36 mm pole cup
Physical
Measurement conditions
- Maximum SPL is the peak level at 1 m, driven with pink noise at crest factor 4 to the clipping point of the recommended amplifier, with the SSOUNDS system preset applied. Full-range enclosures are specified under free-field conditions; figures marked half-space are specified over a reflecting plane, the condition subwoofers are deployed in, which adds approximately 6 dB.
- Frequency response is specified on axis at 1 m in a free field. The tolerance the figure is referenced to is stated alongside it; where no tolerance is given, the figure is the −6 dB bandwidth.
- Sensitivity is specified at 1 W into the nominal impedance at 1 m on axis, averaged across the pass band of the enclosure.
- Coverage angles are nominal −6 dB values averaged across the pass band. Per-octave directivity data is available from SSOUNDS system design support for prediction and modelling.
- Recommended amplifier power is the amplifier output SSOUNDS specifies for this enclosure, driven with the SSOUNDS system preset. It guides amplifier selection and is not an AES power-handling rating for the transducers.
- Nominal impedance is the manufacturer's rating for amplifier load calculation; minimum impedance across the operating band may be lower.
- Net weight excludes packaging, flight case, accessories and optional rigging hardware.
- Dimensions are stated in millimetres and exclude protruding rigging hardware, handles and connector panels unless noted.
- All figures are typical values for production units specified under the conditions above. Individual units may vary within published tolerances.
Directivity
Directivity computed by the SSOUNDS system prediction engine from this product's driver complement, the same dataset the printed data sheet uses. 1/24-octave band-power resolution; values are dB relative to on-axis.
System operation
Recommended: SSOUNDS D14X, up to 2 × XTO 4.6 per channel (two 8 Ω columns in parallel present 4 Ω). Pair with an M-12SUB or M-15SUB per two columns for full-range response.
Downloads
Product documentation, free to open. No registration, no form. The data sheet is a PDF rendered from the page below it; the manual is a print page, so use your browser to print it or save it as PDF.
- Technical data sheetFull specification set with the measurement conditions for each figure, modelled response curves, safety notices and warranty terms.PDF · SS-DS-XTO-46-EN-A4 · Rev. 2608 · Issued 15 Aug 2026
- Technical data sheet, in your browserThe same document as a page, if you would rather read it here or print it yourself.HTML print view · SS-DS-XTO-46-EN-A4 · Rev. 2608 · Issued 15 Aug 2026
- Architectural and engineering specificationThe “shall be” paragraph for tender documents and bills of quantities, written from this product’s own specification rows. Section of the data sheet.HTML section · SS-DS-XTO-46-EN-A4
- User manualUnpacking, connection, installation, operating limits, maintenance schedule and troubleshooting for this model.HTML print view · SS-UM-XTO-46-EN-A4 · Rev. 2608 · Issued 15 Aug 2026
- Directivity table, horizontal axisPolar data in dB relative to on axis, in the layout a measurement rig exports, for prediction and modelling. Computed by the SSOUNDS prediction engine, not measured in an anechoic chamber.CSV download
- Directivity table, vertical axisPolar data in dB relative to on axis, in the layout a measurement rig exports, for prediction and modelling. Computed by the SSOUNDS prediction engine, not measured in an anechoic chamber.CSV download
Loudspeaker data files for prediction software (GLL and CLF for EASE), 2D and 3D drawings and certification documents are issued on request. Email support@s-soundspro.com and we will send the current release for this model.
Amplification
System amplifier named in this product's specifications.
Accessories & recommended
Complete the system with matched components.
SSOUNDS
SSOUNDS XTO Rigging Bumper
Flying frame for XTO columns and compact arrays: perforated multi-position bumper with quick-release pins. TÜV certified.
SSOUNDS
SSOUNDS XTO Fly Joint Bracket
Joint bracket that links XTO 4.6 columns together in a flown or stacked array, with adjustable angle and locking safety pins. TÜV certified.
SSOUNDS
SSOUNDS Flying Bumper for XTO 8P / 4.6
Array rigging frame for XTO 8P and XTO 4.6. M22 shackle standard. TÜV certified.
More from the XTO series
SSOUNDS
SSOUNDS XTO 14P
Cardioid dual 14″ large-format element, 3-way quad-amplified, 153 dB peak, one D34X per box.
FeaturedSSOUNDS
SSOUNDS XTO 12P
Large-format element of the XTO System, 3-way quad-amplified, 149 dB peak SPL from a Socapex-loomed touring element.
FeaturedSSOUNDS
SSOUNDS XTO 10P
Mid-format element of the XTO System, 3-way 10″, 100° constant directivity, 144 dB peak, 0°–14° splay.
SSOUNDS
SSOUNDS XTO 8P
Compact element of the XTO System, 2-way bi-amplified 8″, 110° constant directivity, 141 dB peak, 0°–10° splay.
SSOUNDS
SSOUNDS XTO S218
Dual-18″ subwoofer module of the XTO System, massive, defined low-end with cardioid-ready configuration for touring and stadiums.
SSOUNDS
SSOUNDS XTO S218F
Flown dual-18″ subwoofer module of the XTO System, riding the shared XTO track above or beside the main hangs.