SS-XTO-14X

SSOUNDS · SS-XTO-14X

SSOUNDS XTO 14X

카디오이드 듀얼 14인치 대형 포맷 요소, 3웨이 쿼드 앰프, 153dB 피크, 박스당 D34X 1개.

Request Quote

touringline-arrayFOH

XTO 14X는 XTO System에서 가장 큰 요소이며, 이 제품군이 도달하고자 설계된 최종 지점입니다. 두 개의 14″ 드라이버가 저역을 담당합니다. 심장형 제어는 측면을 향해 방사되는 두 개의 10″ 드라이버에서 나오며, 후방 방사를 상쇄해 뒤쪽으로 향하는 두 번째 어레이 없이도 무대 뒤쪽이 깨끗하게 유지됩니다. 세 번째로 혼 로딩된 10″ 드라이버가 중역을 담당하고, 세 개의 4″-코일 컴프레션 드라이버가 병렬로 혼에 연결됩니다. 캐비닛 하나에서 153 dB 피크. 병렬 연결되는 것은 없습니다. 모든 14X는 자체 D34X를 가지며, 네 개의 섹션이 독립적으로 구동됩니다. 이것이 긴 행잉의 셰이딩을 케이블링이 아닌 프리셋의 문제로 만드는 이유입니다. 나머지 시스템과 동일한 티타늄 3점 리깅, 동일한 Fast-Set 스플레이, 동일한 Socapex 룸, 동일한 프리셋 라이브러리를 갖추고 있어, 14X 메인 행잉과 12P 아웃필이 두 가지가 아닌 하나의 설계 결정이 됩니다. 이것은 스타디움용 박스입니다. 18,000명 이하 수용 규모에서는 12P가 보통 정답입니다.

Part of the XTO System

The largest element. Stadium main hangs, side-firing 10" cardioid cancellation, one D34X per box.

XTO stands for Xtended Touring Output. The large-format touring platform: the elements built for the longest throws and the highest output in the range, rigged and amplified as one system.

The XTO System

Key features

Cardioid by design: 2 × 10″ side-firing drivers for rear cancellation
2 × 14″ low frequency drivers
1 × 10″ horn-loaded midrange
3 × 4″-coil compression drivers in parallel
153 dB peak @ 1 m
70° or 110° × 8° coverage
One D34X per element: four sections, nothing paralleled
Titanium 3-point captive rigging with Fast-Set splay
18 mm and 15 mm Baltic birch with Polyurea finish

Specifications

Engineering data. The conditions each figure is specified under are stated below the table.

General

Type: 3-way line-array element · quad-amplified · cardioid
Certifications: CE · TÜV (rigging system) · EAC · WEEE

Components

Low frequency: 2 × 14″ rear-loaded in angled end chambers
Mid frequency: 2 × 10″ at 45° plus 1 × 10″ horn-loaded
High frequency: 3 × 4″-coil compression drivers, parallel

Acoustic

Frequency response²: 28 Hz – 20 kHz (−10 dB, estimated pending measurement)
Coverage³: 70° or 110° × 8°
Pattern control: Cardioid low frequency by rear-loaded angled end chambers
Maximum SPL¹: 153 dB peak @ 1 m

Electrical

Recommended amplifier power⁴: 24,000 W (one D34X, 4 × 6,000 W @ 4 Ω)
Crossover: 220 Hz · 1,100 Hz
Amplification: Quad-amplified by SSOUNDS D34X system DSP amplifier (LF · MF-direct · MF-horn · HF) · one D34X per element · nothing paralleled
Cabinets per amplifier: 1 · every element shaded independently

Connections

Connectors: 8-pole Socapex input + link output

Rigging

System: High-grade titanium 3-point captive rigging · Fast-Set splay
Splay angles: 0° – 6° adjustable (estimated, pending rigging test data)
Array compatibility: Locks with XTO 12P, XTO 10P and XTO 8P via transition hardware

Physical

Dimensions (H × W × D)⁶: 391 × 1300 × 627 mm
Net weight⁵: 70 kg / 154 lb
Enclosure: 18 mm and 15 mm Baltic birch · Polyurea finish
Colour: Black (custom RAL on request)

Measurement conditions

Maximum SPL is the peak level at 1 m, driven with pink noise at crest factor 4 to the clipping point of the recommended amplifier, with the SSOUNDS system preset applied. Full-range enclosures are specified under free-field conditions; figures marked half-space are specified over a reflecting plane, the condition subwoofers are deployed in, which adds approximately 6 dB.
Frequency response is specified on axis at 1 m in a free field. The tolerance the figure is referenced to is stated alongside it; where no tolerance is given, the figure is the −6 dB bandwidth.
Coverage angles are nominal −6 dB values averaged across the pass band. Per-octave directivity data is available from SSOUNDS system design support for prediction and modelling.
Recommended amplifier power is the amplifier output SSOUNDS specifies for this enclosure, driven with the SSOUNDS system preset. It guides amplifier selection and is not an AES power-handling rating for the transducers.
Net weight excludes packaging, flight case, accessories and optional rigging hardware.
Dimensions are stated in millimetres and exclude protruding rigging hardware, handles and connector panels unless noted.
All figures are typical values for production units specified under the conditions above. Individual units may vary within published tolerances.

System operation

Recommended: one SSOUNDS D34X per XTO 14P. The amplifier's four channels drive the four sections of a single cabinet and nothing is paralleled, so every element in a hang can be gain- and HF-shaded on its own. That is the difference between the 14P and the rest of the range. On XTO 12P two cabinets share a D24X, which is ample resolution for most hangs. On a stadium-length 14P hang the extra resolution is the point: the top of the array and the bottom of the array are doing different jobs. Load the XTO 14P preset and run the 8-pole Socapex loom carrying the four sections. The 14P locks to XTO 12P, 10P and 8P through the standard transition hardware, so a 14P main section can carry a 12P outfill or a 10P downfill in the same hang.

Downloads

Product documentation, free to open. No registration, no form. The data sheet is a PDF rendered from the page below it; the manual is a print page, so use your browser to print it or save it as PDF.

Loudspeaker data files for prediction software (GLL and CLF for EASE), 2D and 3D drawings and certification documents are issued on request. Email support@s-soundspro.com and we will send the current release for this model.

Amplification

System amplifier named in this product's specifications.

SS-D34X

SSOUNDS

SSOUNDS D34X

Coming soon. 4-channel networked DSP amplifier, 4 × 3,000 W at 8 Ω, Dante, AES3 and analog in.

Request QuoteView

SSOUNDS XTO 14X

Key features

Specifications

General

Components

Acoustic

Electrical

Connections

Rigging

Physical

Measurement conditions

System operation

Downloads

Amplification

SSOUNDS D34X

More from the XTO series

SSOUNDS XTO 12P

SSOUNDS XTO 10P

SSOUNDS XTO 8P

SSOUNDS XTO 4.6

SSOUNDS XTO S218

SSOUNDS XTO S218F