SSOUNDS · SS-M10D
SSOUNDS M-10D
10″ two-way loudspeaker with its own amplifier and DSP, Dante audio and PoE power on one network cable.
InstallSpeechCommercialNetworkThe M-10D is a 10″ two-way cabinet for buildings where the audio already travels on the network. Dante audio, Power over Ethernet and control arrive on one Cat cable from a PoE switch; inside, a Class D amplifier drives a 10″ low-frequency driver and a 1.33″ high-frequency driver, and the DSP carries EQ, gain, a limiter and mute, set and monitored with software that also reports the cabinet's status and temperature. It reaches 51 Hz, covers 90° by 60° and mounts on a wall or a base support. We specify it for conference rooms, lecture halls, houses of worship and foyers where a full-range box is wanted without an amplifier rack. Alongside Dante it is AES67-2018 compliant, and its control runs over AES70.
M stands for Modular. One install and portable platform from the smallest fill cabinet to the fifteen-inch point source, with the subwoofers and columns that go with them, on a single amplifier and bracket language.
Key features
- 1 × 10″ LF plus 1 × 1.33″ HF
- 90° × 60° coverage
- 51 Hz to 20 kHz (−10 dB)
- 112 dB maximum SPL at 1 m
- Dante audio, PoE power and control on one RJ45
- Built-in Class D amplifier and DSP, set up with software
- Wall mount or base support, 13.2 kg
Specifications
Engineering data. The conditions each figure is specified under are stated below the table.
General
- Type
- Self-powered two-way loudspeaker, Dante network audio over PoE
- Cooling
- Natural convection, no fan
Components
- Low frequency
- 1 × 10″ driver, 50 mm voice coil
- High frequency
- 1 × 1.33″ driver, 34 mm voice coil
Acoustic
Electrical
- Built-in amplifier
- Class D, 30 W RMS · 60 W music power · 90 W peak into 8 Ω
- Power
- Power over Ethernet: PoE, PoE+ or PoE++ (IEEE 802.3bt, compatible with 802.3at and 802.3af)
- Protection
- Load short-circuit · overcurrent · overtemperature · overload
Connections
- Network
- 1 × RJ45: Dante audio, PoE power and control on one Cat cable
- Audio networking
- Dante · AES67 (AES67-2018)
- Control
- AES70 (AES70-2018) remote control and monitoring with software; reports device status and temperature
- Processing
- Built-in DSP: 5-band EQ, gain, limiter, filter and mute
Rigging
- Mounting
- Wall mount · base support
Measurement conditions
- Maximum SPL is the peak level at 1 m, driven with pink noise at crest factor 4 to the clipping point of the recommended amplifier, with the SSOUNDS system preset applied. Full-range enclosures are specified under free-field conditions; figures marked half-space are specified over a reflecting plane, the condition subwoofers are deployed in, which adds approximately 6 dB.
- Frequency response is specified on axis at 1 m in a free field. The tolerance the figure is referenced to is stated alongside it; where no tolerance is given, the figure is the −6 dB bandwidth.
- Coverage angles are nominal −6 dB values averaged across the pass band. Per-octave directivity data is available from SSOUNDS system design support for prediction and modelling.
- Net weight excludes packaging, flight case, accessories and optional rigging hardware.
- Dimensions are stated in millimetres and exclude protruding rigging hardware, handles and connector panels unless noted.
- All figures are typical values for production units specified under the conditions above. Individual units may vary within published tolerances.
Downloads
Product documentation, free to open. No registration, no form. The data sheet is a PDF rendered from the page below it; the manual is a print page, so use your browser to print it or save it as PDF.
- Technical data sheetFull specification set with the measurement conditions for each figure, modelled response curves, safety notices and warranty terms.PDF · SS-DS-M10D-EN-A4 · Rev. 2610 · Issued 08 Oct 2026
- Technical data sheet, in your browserThe same document as a page, if you would rather read it here or print it yourself.HTML print view · SS-DS-M10D-EN-A4 · Rev. 2610 · Issued 08 Oct 2026
- Architectural and engineering specificationThe “shall be” paragraph for tender documents and bills of quantities, written from this product’s own specification rows. Section of the data sheet.HTML section · SS-DS-M10D-EN-A4
- User manualUnpacking, connection, installation, operating limits, maintenance schedule and troubleshooting for this model.HTML print view · SS-UM-M10D-EN-A4 · Rev. 2610 · Issued 08 Oct 2026
Loudspeaker data files for prediction software (GLL and CLF for EASE), 2D and 3D drawings and certification documents are issued on request. Email support@s-soundspro.com and we will send the current release for this model.
More from the M series
SSOUNDS
SSOUNDS M-15
15″ two-way point source, 55 Hz – 20 kHz, 137 dB peak, passive or bi-amplified.
SSOUNDS
SSOUNDS M-12
12″ full-range point source, mains or floor wedge, the all-rounder of the M-series.
SSOUNDS
SSOUNDS M-12W
12″ two-way coaxial outdoor loudspeaker, IP56, 90° × 90°, 128 dB peak, with 70/100 V taps.
SSOUNDS
SSOUNDS M-10
10″ full-range, compact mains or monitor with strong vocal projection.
SSOUNDS
SSOUNDS M-8
8″ full-range, high-output multipurpose box for portable PA, fill and install.
SSOUNDS
SSOUNDS M-8W
8″ two-way coaxial outdoor loudspeaker, IP56, 120° × 120°, 124 dB peak.