SSOUNDS · SS-XTO-14P
SSOUNDS XTO 14P
Élément cardioïde double 14″ grand format, 3 voies quadri-amplifié, 153 dB crête, un D34X par enceinte.
Le XTO 14P est le plus grand élément du système XTO et l'enceinte vers laquelle la gamme a été conçue. Deux haut-parleurs de 14″ sont chargés à l'arrière dans des chambres d'extrémité inclinées, offrant un contrôle de directivité en bas de bande plutôt que seulement au-dessus, de sorte que l'arrière de la scène reste propre sans avoir besoin d'un second réseau pointé vers l'arrière. Au-dessus, deux cônes de 10″ à 45° flanquent un troisième 10″ chargé par pavillon, et trois moteurs de compression à bobine de 4″ fonctionnent en parallèle dans le pavillon. 153 dB crête pour une seule enceinte. Rien n'est mis en parallèle. Chaque 14P possède son propre D34X, quatre sections pilotées indépendamment, ce qui fait de l'atténuation d'un long accrochage une question de préréglage plutôt que de câblage. Il reprend le même accrochage titane trois points, la même ouverture Fast-Set, le même faisceau Socapex et la même bibliothèque de préréglages que le reste du système, de sorte qu'un accrochage principal en 14P et un complément en 12P relèvent d'une seule décision de conception, et non de deux. C'est une enceinte de stade. En dessous de 18 000 places, le 12P est généralement la bonne réponse.
Part of the XTO System
The largest element. Stadium main hangs, cardioid at the bottom of the band, one D34X per box.
XTO stands for Xtended Touring Output. The large-format touring platform: the elements built for the longest throws and the highest output in the range, rigged and amplified as one system.
Key features
- Cardioid by design: 2 × 14″ rear-loaded in angled end chambers
- 2 × 10″ at 45° plus 1 × 10″ horn-loaded midrange
- 3 × 4″-coil compression drivers in parallel
- 153 dB peak @ 1 m
- 70° or 110° × 8° coverage
- One D34X per element: four sections, nothing paralleled
- Titanium 3-point captive rigging with Fast-Set splay
- 18 mm and 15 mm Baltic birch with Polyurea finish
Specifications
Engineering data. The conditions each figure is specified under are stated below the table.
General
- Type
- 3-way line-array element · quad-amplified · cardioid
- Certifications
- CE · TÜV (rigging system) · EAC · WEEE
Components
- Low frequency
- 2 × 14″ rear-loaded in angled end chambers
- Mid frequency
- 2 × 10″ at 45° plus 1 × 10″ horn-loaded
- High frequency
- 3 × 4″-coil compression drivers, parallel
Acoustic
Electrical
- Recommended amplifier power4
- 24,000 W (one D34X, 4 × 6,000 W @ 4 Ω)
- Crossover
- 220 Hz · 1,100 Hz
- Amplification
- Quad-amplified by SSOUNDS D34X system DSP amplifier (LF · MF-direct · MF-horn · HF) · one D34X per element · nothing paralleled
- Cabinets per amplifier
- 1 · every element shaded independently
Connections
- Connectors
- 8-pole Socapex input + link output
Rigging
- System
- High-grade titanium 3-point captive rigging · Fast-Set splay
- Splay angles
- 0° – 6° adjustable (estimated, pending rigging test data)
- Array compatibility
- Locks with XTO 12P, XTO 10P and XTO 8P via transition hardware
Physical
Measurement conditions
- Maximum SPL is the peak level at 1 m, driven with pink noise at crest factor 4 to the clipping point of the recommended amplifier, with the SSOUNDS system preset applied. Full-range enclosures are specified under free-field conditions; figures marked half-space are specified over a reflecting plane, the condition subwoofers are deployed in, which adds approximately 6 dB.
- Frequency response is specified on axis at 1 m in a free field. The tolerance the figure is referenced to is stated alongside it; where no tolerance is given, the figure is the −6 dB bandwidth.
- Coverage angles are nominal −6 dB values averaged across the pass band. Per-octave directivity data is available from SSOUNDS system design support for prediction and modelling.
- Recommended amplifier power is the amplifier output SSOUNDS specifies for this enclosure, driven with the SSOUNDS system preset. It guides amplifier selection and is not an AES power-handling rating for the transducers.
- Net weight excludes packaging, flight case, accessories and optional rigging hardware.
- Dimensions are stated in millimetres and exclude protruding rigging hardware, handles and connector panels unless noted.
- All figures are typical values for production units specified under the conditions above. Individual units may vary within published tolerances.
System operation
Recommended: one SSOUNDS D34X per XTO 14P. The amplifier's four channels drive the four sections of a single cabinet and nothing is paralleled, so every element in a hang can be gain- and HF-shaded on its own. That is the difference between the 14P and the rest of the range. On XTO 12P two cabinets share a D24X, which is ample resolution for most hangs. On a stadium-length 14P hang the extra resolution is the point: the top of the array and the bottom of the array are doing different jobs. Load the XTO 14P preset and run the 8-pole Socapex loom carrying the four sections. The 14P locks to XTO 12P, 10P and 8P through the standard transition hardware, so a 14P main section can carry a 12P outfill or a 10P downfill in the same hang.
Downloads
Product documentation, free to open. No registration, no form. The data sheet is a PDF rendered from the page below it; the manual is a print page, so use your browser to print it or save it as PDF.
- Technical data sheetFull specification set with the measurement conditions for each figure, modelled response curves, safety notices and warranty terms.HTML print view · SS-DS-XTO-14P-EN-A4 · Rev. 2609 · Issued 11 Sept 2026
- Architectural and engineering specificationThe “shall be” paragraph for tender documents and bills of quantities, written from this product’s own specification rows. Section of the data sheet.HTML section · SS-DS-XTO-14P-EN-A4
- User manualUnpacking, connection, installation, operating limits, maintenance schedule and troubleshooting for this model.HTML print view · SS-UM-XTO-14P-EN-A4 · Rev. 2609 · Issued 11 Sept 2026
Loudspeaker data files for prediction software (GLL and CLF for EASE), 2D and 3D drawings and certification documents are issued on request. Email support@s-soundspro.com and we will send the current release for this model.
Amplification
System amplifier named in this product's specifications.
More from the XTO series
FeaturedSSOUNDS
SSOUNDS XTO 12P
Large-format element of the XTO System, 3-way quad-amplified, 149 dB peak SPL from a Socapex-loomed touring element.
FeaturedSSOUNDS
SSOUNDS XTO 10P
Mid-format element of the XTO System, 3-way 10″, 100° constant directivity, 144 dB peak, 0°–14° splay.
SSOUNDS
SSOUNDS XTO 8P
Compact element of the XTO System, 2-way bi-amplified 8″, 110° constant directivity, 141 dB peak, 0°–10° splay.
SSOUNDS
SSOUNDS XTO 4.6
Column element of the XTO System, passive line array, 4 × 6.5″ drivers, 65 Hz – 20 kHz and 134 dB peak in a sightline-friendly column.
SSOUNDS
SSOUNDS XTO S218
Dual-18″ subwoofer module of the XTO System, massive, defined low-end with cardioid-ready configuration for touring and stadiums.
SSOUNDS
SSOUNDS XTO S218F
Flown dual-18″ subwoofer module of the XTO System, riding the shared XTO track above or beside the main hangs.