SS-XTO-14P

SSOUNDS · SS-XTO-14P

SSOUNDS XTO 14P

카디오이드 듀얼 14인치 대형 포맷 요소, 3웨이 쿼드 앰프, 153dB 피크, 박스당 D34X 1개.

Request Quote

touringline-arrayFOH

XTO 14P는 XTO 시스템에서 가장 큰 요소이자, 이 시리즈가 궁극적으로 도달하도록 설계된 박스입니다. 두 개의 14인치 드라이버가 각진 엔드 챔버에 후면 로딩되어, 대역 하단에서도 패턴 제어를 제공합니다. 이는 단지 상위 대역에서만이 아니라, 뒤쪽을 향한 두 번째 어레이 없이도 스테이지 후면을 깨끗하게 유지합니다. 그 위에는 45° 각도로 두 개의 10인치 콘이 세 번째 혼 로딩 10인치를 양옆에서 받치고, 세 개의 4인치 코일 컴프레션 드라이버가 혼에 병렬로 연결됩니다. 단일 캐비닛에서 153dB 피크를 냅니다. 어떤 것도 병렬로 연결되지 않습니다. 각 14P는 자체 D34X를 사용하며, 네 개의 섹션이 독립적으로 구동됩니다. 이는 긴 행잉에서 셰이딩을 케이블링 문제가 아닌 프리셋 문제로 만드는 핵심입니다. 시스템의 나머지 부분과 동일한 티타늄 3포인트 리깅, 동일한 Fast-Set 스플레이, 동일한 Socapex 룸, 동일한 프리셋 라이브러리를 공유하므로, 14P 메인 행잉과 12P 아웃필은 두 가지 설계 결정이 아니라 하나의 설계 결정입니다. 이것은 스타디움용 박스입니다. 수용 인원 18,000명 미만에서는 일반적으로 12P가 올바른 선택입니다.

Part of the XTO System

The largest element. Stadium main hangs, cardioid at the bottom of the band, one D34X per box.

XTO stands for Xtended Touring Output. The large-format touring platform: the elements built for the longest throws and the highest output in the range, rigged and amplified as one system.

The XTO System

Key features

Cardioid by design: 2 × 14″ rear-loaded in angled end chambers
2 × 10″ at 45° plus 1 × 10″ horn-loaded midrange
3 × 4″-coil compression drivers in parallel
153 dB peak @ 1 m
70° or 110° × 8° coverage
One D34X per element: four sections, nothing paralleled
Titanium 3-point captive rigging with Fast-Set splay
18 mm and 15 mm Baltic birch with Polyurea finish

Specifications

Engineering data. The conditions each figure is specified under are stated below the table.

General

Type: 3-way line-array element · quad-amplified · cardioid
Certifications: CE · TÜV (rigging system) · EAC · WEEE

Components

Low frequency: 2 × 14″ rear-loaded in angled end chambers
Mid frequency: 2 × 10″ at 45° plus 1 × 10″ horn-loaded
High frequency: 3 × 4″-coil compression drivers, parallel

Acoustic

Frequency response²: 28 Hz – 20 kHz (−10 dB, estimated pending measurement)
Coverage³: 70° or 110° × 8°
Pattern control: Cardioid low frequency by rear-loaded angled end chambers
Maximum SPL¹: 153 dB peak @ 1 m

Electrical

Recommended amplifier power⁴: 24,000 W (one D34X, 4 × 6,000 W @ 4 Ω)
Crossover: 220 Hz · 1,100 Hz
Amplification: Quad-amplified by SSOUNDS D34X system DSP amplifier (LF · MF-direct · MF-horn · HF) · one D34X per element · nothing paralleled
Cabinets per amplifier: 1 · every element shaded independently

Connections

Connectors: 8-pole Socapex input + link output

Rigging

System: High-grade titanium 3-point captive rigging · Fast-Set splay
Splay angles: 0° – 6° adjustable (estimated, pending rigging test data)
Array compatibility: Locks with XTO 12P, XTO 10P and XTO 8P via transition hardware

Physical

Dimensions (H × W × D)⁶: 391 × 1300 × 627 mm (estimated from reference-class geometry, pending SSOUNDS enclosure drawing)
Net weight⁵: 70 kg / 154 lb
Enclosure: 18 mm and 15 mm Baltic birch · Polyurea finish
Colour: Black (custom RAL on request)

Measurement conditions

Maximum SPL is the peak level at 1 m, driven with pink noise at crest factor 4 to the clipping point of the recommended amplifier, with the SSOUNDS system preset applied. Full-range enclosures are specified under free-field conditions; figures marked half-space are specified over a reflecting plane, the condition subwoofers are deployed in, which adds approximately 6 dB.
Frequency response is specified on axis at 1 m in a free field. The tolerance the figure is referenced to is stated alongside it; where no tolerance is given, the figure is the −6 dB bandwidth.
Coverage angles are nominal −6 dB values averaged across the pass band. Per-octave directivity data is available from SSOUNDS system design support for prediction and modelling.
Recommended amplifier power is the amplifier output SSOUNDS specifies for this enclosure, driven with the SSOUNDS system preset. It guides amplifier selection and is not an AES power-handling rating for the transducers.
Net weight excludes packaging, flight case, accessories and optional rigging hardware.
Dimensions are stated in millimetres and exclude protruding rigging hardware, handles and connector panels unless noted.
All figures are typical values for production units specified under the conditions above. Individual units may vary within published tolerances.

System operation

Recommended: one SSOUNDS D34X per XTO 14P. The amplifier's four channels drive the four sections of a single cabinet and nothing is paralleled, so every element in a hang can be gain- and HF-shaded on its own. That is the difference between the 14P and the rest of the range. On XTO 12P two cabinets share a D24X, which is ample resolution for most hangs. On a stadium-length 14P hang the extra resolution is the point: the top of the array and the bottom of the array are doing different jobs. Load the XTO 14P preset and run the 8-pole Socapex loom carrying the four sections. The 14P locks to XTO 12P, 10P and 8P through the standard transition hardware, so a 14P main section can carry a 12P outfill or a 10P downfill in the same hang.

Downloads

Product documentation, free to open. No registration, no form. The data sheet is a PDF rendered from the page below it; the manual is a print page, so use your browser to print it or save it as PDF.

Loudspeaker data files for prediction software (GLL and CLF for EASE), 2D and 3D drawings and certification documents are issued on request. Email support@s-soundspro.com and we will send the current release for this model.

Amplification

System amplifier named in this product's specifications.

SS-D34X

SSOUNDS

SSOUNDS D34X

Coming soon. 4-channel networked DSP amplifier, 4 × 3,000 W at 8 Ω, Dante, AES3 and analog in.

Request QuoteView

SSOUNDS XTO 14P

Key features

Specifications

General

Components

Acoustic

Electrical

Connections

Rigging

Physical

Measurement conditions

System operation

Downloads

Amplification

SSOUNDS D34X

More from the XTO series

SSOUNDS XTO 12P

SSOUNDS XTO 10P

SSOUNDS XTO 8P

SSOUNDS XTO 4.6

SSOUNDS XTO S218

SSOUNDS XTO S218F