SSOUNDS · SS-CL6P
SSOUNDS CL6P
6.5″ two-way pendant speaker for open ceilings, the CL6's drivers and 70/100 V tapping in a suspended housing.
Warehouse retail, restaurants with exposed services, atria and concourses often have no ceiling to cut a hole in. The CL6P carries the CL6's 6.5″ coaxial driver and 0.75″ tweeter in a pendant housing that hangs from the structure, with the same 130° conical pattern, 70 / 100 V tapping at 15, 7.5 or 3.75 W, or 8 Ω operation, so a pendant zone and a ceiling zone can share one amplifier and one design. We specify it for retail, hospitality, open-plan offices and any room where the services are on show.
CL stands for Ceiling Loudspeaker. Loudspeakers that mount in or hang from the ceiling, for distributed speech and music: the number is the driver size, P marks the pendant that hangs where there is no ceiling to cut, HD the Dante model that takes audio and power over one network cable, and SUB the ceiling subwoofer.
Key features
- 6.5″ coaxial woofer + 0.75″ balanced-dome tweeter
- 130° conical coverage
- 70 Hz to 20 kHz (−10 dB)
- 108 dB peak at 1 m, 88 dB sensitivity
- 70 / 100 V tapped (15 / 7.5 / 3.75 W) or 8 Ω
- Pendant housing for open ceilings
Specifications
Engineering data. The conditions each figure is specified under are stated below the table.
General
- Type
- Passive 2-way coaxial pendant speaker
Components
- Drivers
- 6.5″ coaxial woofer + 0.75″ balanced-dome tweeter
Acoustic
Electrical
- Recommended amplifier power5
- 60 W (8 Ω low-Z)
- Operation
- 70 / 100 V line (tapped) or 8 Ω low-Z
- Taps (100 V)
- 15 / 7.5 / 3.75 W
Connections
- Connectors
- Screw terminal
Rigging
- Mounting
- Pendant, suspended
- Safety attachment
- 4 mm steel safety cable, supplied (secondary suspension, independent of the hanging cable)
Measurement conditions
- Maximum SPL is the peak level at 1 m, driven with pink noise at crest factor 4 to the clipping point of the recommended amplifier, with the SSOUNDS system preset applied. Full-range enclosures are specified under free-field conditions; figures marked half-space are specified over a reflecting plane, the condition subwoofers are deployed in, which adds approximately 6 dB.
- Frequency response is specified on axis at 1 m in a free field. The tolerance the figure is referenced to is stated alongside it; where no tolerance is given, the figure is the −6 dB bandwidth.
- Sensitivity is specified at 1 W into the nominal impedance at 1 m on axis, averaged across the pass band of the enclosure.
- Coverage angles are nominal −6 dB values averaged across the pass band. Per-octave directivity data is available from SSOUNDS system design support for prediction and modelling.
- Recommended amplifier power is the amplifier output SSOUNDS specifies for this enclosure, driven with the SSOUNDS system preset. It guides amplifier selection and is not an AES power-handling rating for the transducers.
- All figures are typical values for production units specified under the conditions above. Individual units may vary within published tolerances.
Downloads
Product documentation, free to open. No registration, no form. The data sheet is a PDF rendered from the page below it; the manual is a print page, so use your browser to print it or save it as PDF.
- Technical data sheetFull specification set with the measurement conditions for each figure, modelled response curves, safety notices and warranty terms.PDF · SS-DS-CL6P-EN-A4 · Rev. 2610 · Issued 09 Oct 2026
- Technical data sheet, in your browserThe same document as a page, if you would rather read it here or print it yourself.HTML print view · SS-DS-CL6P-EN-A4 · Rev. 2610 · Issued 09 Oct 2026
- Architectural and engineering specificationThe “shall be” paragraph for tender documents and bills of quantities, written from this product’s own specification rows. Section of the data sheet.HTML section · SS-DS-CL6P-EN-A4
- User manualUnpacking, connection, installation, operating limits, maintenance schedule and troubleshooting for this model.HTML print view · SS-UM-CL6P-EN-A4 · Rev. 2610 · Issued 09 Oct 2026
Loudspeaker data files for prediction software (GLL and CLF for EASE), 2D and 3D drawings and certification documents are issued on request. Email support@s-soundspro.com and we will send the current release for this model.
More from the CL series
SSOUNDS
SSOUNDS CL8SUB
8″ in-ceiling subwoofer in a back-can with spring-tab mounting, the low end under CL6 and CL8 ceiling zones.
SSOUNDS
SSOUNDS CL8
8″ two-way ceiling speaker, full-range background and foreground audio with 70/100 V tapping.
SSOUNDS
SSOUNDS CL8HD
8″ two-way ceiling speaker with its own amplifier and DSP, Dante audio and PoE power on one network cable.
SSOUNDS
SSOUNDS CL6
6.5″ two-way ceiling speaker, discreet, even distributed audio with 70/100 V tapping.
SSOUNDS
SSOUNDS CL6HD
6.5″ two-way ceiling speaker with its own amplifier and DSP, Dante audio and PoE power on one network cable.