SSOUNDS · SS-XTO-S218F
SSOUNDS XTO S218F
Módulo subwoofer duplo de 18″ voando do Sistema XTO, montado no trilho XTO compartilhado acima ou ao lado dos hangs principais.
O XTO S218F é a versão voadora do XTO S218. Mesmo design acústico de duplo 18″, mesma configuração pronta para cardioide, rigging diferente: ele usa o trilho XTO compartilhado, então voa acima do hang principal ou em sua própria coluna ao lado dele, sem uma linguagem de rigging separada ou uma lista de peças de reposição separada. Voar o grave em vez de empilhá-lo é o que garante cobertura uniforme de frente para trás em um estádio em concha, e uma coluna cardioide voadora é o que o mantém longe do palco e fora dos assentos atrás do array. Arcos empilhados no chão e blocos end-fire ainda têm seu lugar, e o S218 continua sendo a caixa para isso; a maioria dos grandes sistemas acaba usando ambos.
Part of the XTO System
The flown dual-18. Rides the shared track above or beside the main hangs, cardioid ready.
XTO stands for Xtended Touring Output. The large-format touring platform: the elements built for the longest throws and the highest output in the range, rigged and amplified as one system.
Key features
- Flown dual-18″ subwoofer module of the XTO System
- Rides the shared XTO track above or beside the main hangs
- Cardioid ready
- Same acoustic design as the ground-stacked XTO S218
- One D24X channel per subwoofer
Specifications
Engineering data. The conditions each figure is specified under are stated below the table.
General
- Type
- Bandpass dual-18″ flown touring subwoofer
- Certifications
- CE · TÜV · EAC · WEEE
Components
- Low frequency
- 2 × 18″ cone drivers, 5″ coil
Acoustic
Electrical
Connections
- Connectors
- 2 × NL4 speakON (in / link)
- Pin map
- 1+/1− SUB · 2+/2− not linked
Rigging
- System
- Shared XTO fly track · 3-point captive pins · flies above or beside the main hang
Physical
- Enclosure
- 18 mm Baltic birch · Polyurea finish
- Grille
- Powder-coated perforated steel with acoustic cloth backing
- Handles
- 2 side recessed
- Colour
- Black (custom RAL on request)
Measurement conditions
- Maximum SPL is the peak level at 1 m, driven with pink noise at crest factor 4 to the clipping point of the recommended amplifier, with the SSOUNDS system preset applied. Full-range enclosures are specified under free-field conditions; figures marked half-space are specified over a reflecting plane, the condition subwoofers are deployed in, which adds approximately 6 dB.
- Frequency response is specified on axis at 1 m in a free field. The tolerance the figure is referenced to is stated alongside it; where no tolerance is given, the figure is the −6 dB bandwidth.
- Sensitivity is specified at 1 W into the nominal impedance at 1 m on axis, averaged across the pass band of the enclosure.
- Recommended amplifier power is the amplifier output SSOUNDS specifies for this enclosure, driven with the SSOUNDS system preset. It guides amplifier selection and is not an AES power-handling rating for the transducers.
- Nominal impedance is the manufacturer's rating for amplifier load calculation; minimum impedance across the operating band may be lower.
- All figures are typical values for production units specified under the conditions above. Individual units may vary within published tolerances.
System operation
Recommended: SSOUNDS D24X, one channel per XTO S218F (4 Ω) with the S218 preset loaded. Cardioid presets are supplied for three- and four-box columns. A flown subwoofer column is normally run as its own zone, so its arrival time and its cardioid rear rejection can be set independently of the ground-stacked arcs.
Downloads
Product documentation, free to open. No registration, no form. The data sheet is a PDF rendered from the page below it; the manual is a print page, so use your browser to print it or save it as PDF.
- Technical data sheetFull specification set with the measurement conditions for each figure, modelled response curves, safety notices and warranty terms.HTML print view · SS-DS-XTO-S218F-EN-A4 · Rev. 2609 · Issued 09 Sept 2026
- Architectural and engineering specificationThe “shall be” paragraph for tender documents and bills of quantities, written from this product’s own specification rows. Section of the data sheet.HTML section · SS-DS-XTO-S218F-EN-A4
- User manualUnpacking, connection, installation, operating limits, maintenance schedule and troubleshooting for this model.HTML print view · SS-UM-XTO-S218F-EN-A4 · Rev. 2609 · Issued 09 Sept 2026
Loudspeaker data files for prediction software (GLL and CLF for EASE), 2D and 3D drawings and certification documents are issued on request. Email support@s-soundspro.com and we will send the current release for this model.
Amplification
System amplifier named in this product's specifications.
More from the XTO series
SSOUNDS
SSOUNDS XTO 14P
Cardioid dual 14″ large-format element, 3-way quad-amplified, 153 dB peak, one D34X per box.
FeaturedSSOUNDS
SSOUNDS XTO 12P
Large-format element of the XTO System, 3-way quad-amplified, 149 dB peak SPL from a Socapex-loomed touring element.
FeaturedSSOUNDS
SSOUNDS XTO 10P
Mid-format element of the XTO System, 3-way 10″, 100° constant directivity, 144 dB peak, 0°–14° splay.
SSOUNDS
SSOUNDS XTO 8P
Compact element of the XTO System, 2-way bi-amplified 8″, 110° constant directivity, 141 dB peak, 0°–10° splay.
SSOUNDS
SSOUNDS XTO 4.6
Column element of the XTO System, passive line array, 4 × 6.5″ drivers, 65 Hz – 20 kHz and 134 dB peak in a sightline-friendly column.
SSOUNDS
SSOUNDS XTO S218
Dual-18″ subwoofer module of the XTO System, massive, defined low-end with cardioid-ready configuration for touring and stadiums.