1 / 3SSOUNDS · SS-P10T
SSOUNDS P10T
Three-way 10″ install loudspeaker in an IP67 moulded ABS cabinet, 50 Hz to 20 kHz, on a 70/100 V line or at 8 Ω, for worship, hospitality, retail, courtyards and conference rooms.
Restaurants, shops, meeting rooms, courtyards and the side areas of a prayer hall need a loudspeaker that sounds full with music, stays clear with speech, and sits on a wall indoors or out without looking like stage equipment. The P10T is a commercial-install point source in the same 10″ format as our wooden M-10: a passive three-way cabinet with a 10″ low-frequency driver, a 5″ mid and a 1″ high-frequency driver in a moulded ABS enclosure rated IP67, with a spray finish and a powder-coated steel grille, in black or white. It reaches 50 Hz, covers 90° by 60°, and mounts on a wall bracket. It runs either on a 70/100 V distributed line or at 8 Ω from an amplifier channel, and the connector is chosen at order, screw-terminal plug-in, NL4 speakON or banana binding posts, so it lands on whatever cable the installer is already running. We specify it for houses of worship, mosques and their courtyards, restaurants, retail, conference rooms, covered outdoor areas and background or foreground music.
P stands for Point Source. One cabinet as the whole source rather than a coupled array: coverage is set by the cabinet's own horn, waveguide or driver layout, and is the same whether one is deployed or several. A T marks a model that also runs on a 70/100 V line.
Key features
- Three-way: 1 × 10″ LF, 1 × 5″ mid, 1 × 1″ HF
- 50 Hz to 20 kHz (−10 dB)
- 90° × 60° coverage
- 99 dB sensitivity, 129 dB peak at 1 m
- 300 W power handling, 600 W recommended amplifier
- 70/100 V line or 8 Ω low-Z
- IP67 moulded ABS cabinet, black or white, wall bracket, 8.6 kg
- Connector specified at order: screw terminal, NL4 speakON or binding posts
Specifications
Engineering data. The conditions each figure is specified under are stated below the table.
General
- Type
- Passive 3-way full-range, ABS install cabinet
Components
- Low frequency
- 1 × 10″ driver
- Mid frequency
- 1 × 5″ driver
- High frequency
- 1 × 1″ driver
Acoustic
Electrical
- Amplification
- Passive, one channel of a SSOUNDS D14X system DSP amplifier per cabinet (4 cabinets per amplifier)
- Power handling5
- 300 W
- Recommended amplifier power6
- 600 W
- Nominal impedance7
- 8 Ω
- Operation
- 70 / 100 V line (tapped) or 8 Ω low-Z
- Taps (100 V)
- 8 Ω / 25 / 50 / 100 W
- Taps (70 V)
- 8 Ω / 12.5 / 25 / 50 W
- Crossover
- Passive 3-way
Connections
- Connectors
- Specified at order: screw-terminal plug-in, NL4 speakON or banana binding posts (in / link)
Rigging
- Mounting
- Wall bracket
Physical
Environment
- Ingress protection
- IP67
Measurement conditions
- Maximum SPL is the peak level at 1 m, driven with pink noise at crest factor 4 to the clipping point of the recommended amplifier, with the SSOUNDS system preset applied. Full-range enclosures are specified under free-field conditions; figures marked half-space are specified over a reflecting plane, the condition subwoofers are deployed in, which adds approximately 6 dB.
- Frequency response is specified on axis at 1 m in a free field. The tolerance the figure is referenced to is stated alongside it; where no tolerance is given, the figure is the −6 dB bandwidth.
- Sensitivity is specified at 1 W into the nominal impedance at 1 m on axis, averaged across the pass band of the enclosure.
- Coverage angles are nominal −6 dB values averaged across the pass band. Per-octave directivity data is available from SSOUNDS system design support for prediction and modelling.
- Power handling is rated to AES2 using pink noise with a 6 dB crest factor over a two-hour period. Programme power is twice the AES rating; peak power is four times.
- Recommended amplifier power is the amplifier output SSOUNDS specifies for this enclosure, driven with the SSOUNDS system preset. It guides amplifier selection and is not an AES power-handling rating for the transducers.
- Nominal impedance is the manufacturer's rating for amplifier load calculation; minimum impedance across the operating band may be lower.
- Net weight excludes packaging, flight case, accessories and optional rigging hardware.
- Dimensions are stated in millimetres and exclude protruding rigging hardware, handles and connector panels unless noted.
- All figures are typical values for production units specified under the conditions above. Individual units may vary within published tolerances.
Directivity
Directivity computed by the SSOUNDS system prediction engine from this product's driver complement, the same dataset the printed data sheet uses. 1/24-octave band-power resolution; values are dB relative to on-axis.
Downloads
Product documentation, free to open. No registration, no form. The data sheet is a PDF rendered from the page below it; the manual is a print page, so use your browser to print it or save it as PDF.
- Technical data sheetFull specification set with the measurement conditions for each figure, modelled response curves, safety notices and warranty terms.PDF · SS-DS-P10T-EN-A4 · Rev. 2610 · Issued 09 Oct 2026
- Technical data sheet, in your browserThe same document as a page, if you would rather read it here or print it yourself.HTML print view · SS-DS-P10T-EN-A4 · Rev. 2610 · Issued 09 Oct 2026
- Architectural and engineering specificationThe “shall be” paragraph for tender documents and bills of quantities, written from this product’s own specification rows. Section of the data sheet.HTML section · SS-DS-P10T-EN-A4
- User manualUnpacking, connection, installation, operating limits, maintenance schedule and troubleshooting for this model.HTML print view · SS-UM-P10T-EN-A4 · Rev. 2610 · Issued 09 Oct 2026
- Directivity table, horizontal axisPolar data in dB relative to on axis, in the layout a measurement rig exports, for prediction and modelling. Computed by the SSOUNDS prediction engine, not measured in an anechoic chamber.CSV download
- Directivity table, vertical axisPolar data in dB relative to on axis, in the layout a measurement rig exports, for prediction and modelling. Computed by the SSOUNDS prediction engine, not measured in an anechoic chamber.CSV download
Loudspeaker data files for prediction software (GLL and CLF for EASE), 2D and 3D drawings and certification documents are issued on request. Email support@s-soundspro.com and we will send the current release for this model.
Amplification
System amplifier named in this product's specifications.
More from the P series
SSOUNDS
SSOUNDS P15-X
3-way long-throw point source, 2 × 15″, 4 × 6.5″ and 2 × 3″ behind a 70° × 40° waveguide, 2,000 W.
SSOUNDS
SSOUNDS P15-XA
Active tri-amplified P15-X, same 3-way long-throw package with full DSP control of each section.
SSOUNDS
SSOUNDS P15
Two-way dual-15″ point source, high-output mains and fill with a rotatable constant-directivity horn.
SSOUNDS
SSOUNDS P12T
Two-way 12″ install point source in a portrait birch cabinet, yoke mounted, on a 70/100 V line or at 8 Ω.
SSOUNDS
SSOUNDS P6T
Two-way 6.5″ install loudspeaker in a moulded ABS cabinet, 80 Hz to 20 kHz, 90° × 60°, on a 70/100 V line or at 8 Ω.
SSOUNDS
SSOUNDS P5
Three-way 5″ install loudspeaker for wall and corner mounting, 120° × 90°, in a slim white aluminium cabinet.