SSOUNDS · SS-P5
SSOUNDS P5
Three-way 5″ install loudspeaker for wall and corner mounting, 120° × 90°, in a slim white aluminium cabinet.
Meeting rooms, classrooms and shops often have one usable position: flat on a wall or tucked into a corner. The P5 is a three-way install cabinet built for exactly that. A 5″ low-frequency driver, four 3″ mid drivers and a 3″ high-frequency driver sit on angled faces of a slim aluminium cabinet, so the box carries its own aim and spreads 120° by 90° from 120 Hz to 18 kHz without a bracket to adjust. It handles 150 W at 8 Ω, reaches 120 dB at 1 m and connects on two Euroblock sockets. We specify it for meeting rooms, classrooms, retail, restaurants and corridors.
P stands for Point Source. One cabinet as the whole source rather than a coupled array: coverage is set by the cabinet's own horn, waveguide or driver layout, and is the same whether one is deployed or several. A T marks a model that also runs on a 70/100 V line.
Key features
- Three-way: 1 × 5″ LF, 4 × 3″ MF, 1 × 3″ HF
- 120° × 90° coverage
- 120 Hz to 18 kHz
- 95 dB sensitivity, 120 dB maximum SPL at 1 m
- 150 W rated power, 300 W recommended amplifier, 8 Ω
- Slim aluminium cabinet for wall and corner mounting, 6.6 kg
Specifications
Engineering data. The conditions each figure is specified under are stated below the table.
General
- Type
- Passive 3-way install loudspeaker, wall and corner mounting
Components
- Low frequency
- 1 × 5″ driver
- Mid frequency
- 4 × 3″ drivers
- High frequency
- 1 × 3″ driver
Acoustic
Connections
- Connectors
- 2 × Euroblock
Rigging
- Mounting
- Wall or corner, angle built into the cabinet
Physical
Measurement conditions
- Maximum SPL is the peak level at 1 m, driven with pink noise at crest factor 4 to the clipping point of the recommended amplifier, with the SSOUNDS system preset applied. Full-range enclosures are specified under free-field conditions; figures marked half-space are specified over a reflecting plane, the condition subwoofers are deployed in, which adds approximately 6 dB.
- Frequency response is specified on axis at 1 m in a free field. The tolerance the figure is referenced to is stated alongside it; where no tolerance is given, the figure is the −6 dB bandwidth.
- Sensitivity is specified at 1 W into the nominal impedance at 1 m on axis, averaged across the pass band of the enclosure.
- Coverage angles are nominal −6 dB values averaged across the pass band. Per-octave directivity data is available from SSOUNDS system design support for prediction and modelling.
- Recommended amplifier power is the amplifier output SSOUNDS specifies for this enclosure, driven with the SSOUNDS system preset. It guides amplifier selection and is not an AES power-handling rating for the transducers.
- Nominal impedance is the manufacturer's rating for amplifier load calculation; minimum impedance across the operating band may be lower.
- Net weight excludes packaging, flight case, accessories and optional rigging hardware.
- Dimensions are stated in millimetres and exclude protruding rigging hardware, handles and connector panels unless noted.
- All figures are typical values for production units specified under the conditions above. Individual units may vary within published tolerances.
Downloads
Product documentation, free to open. No registration, no form. The data sheet is a PDF rendered from the page below it; the manual is a print page, so use your browser to print it or save it as PDF.
- Technical data sheetFull specification set with the measurement conditions for each figure, modelled response curves, safety notices and warranty terms.HTML print view · SS-DS-P5-EN-A4 · Rev. 2610 · Issued 09 Oct 2026
- Architectural and engineering specificationThe “shall be” paragraph for tender documents and bills of quantities, written from this product’s own specification rows. Section of the data sheet.HTML section · SS-DS-P5-EN-A4
- User manualUnpacking, connection, installation, operating limits, maintenance schedule and troubleshooting for this model.HTML print view · SS-UM-P5-EN-A4 · Rev. 2610 · Issued 09 Oct 2026
Loudspeaker data files for prediction software (GLL and CLF for EASE), 2D and 3D drawings and certification documents are issued on request. Email support@s-soundspro.com and we will send the current release for this model.
More from the P series
SSOUNDS
SSOUNDS P15-X
3-way long-throw point source, 2 × 15″, 4 × 6.5″ and 2 × 3″ behind a 70° × 40° waveguide, 2,000 W.
SSOUNDS
SSOUNDS P15-XA
Active tri-amplified P15-X, same 3-way long-throw package with full DSP control of each section.
SSOUNDS
SSOUNDS P15
Two-way dual-15″ point source, high-output mains and fill with a rotatable constant-directivity horn.
SSOUNDS
SSOUNDS P12T
Two-way 12″ install point source in a portrait birch cabinet, yoke mounted, on a 70/100 V line or at 8 Ω.
SSOUNDS
SSOUNDS P10T
Three-way 10″ install loudspeaker in an IP67 moulded ABS cabinet, 50 Hz to 20 kHz, on a 70/100 V line or at 8 Ω, for worship, hospitality, retail, courtyards and conference rooms.
SSOUNDS
SSOUNDS P6T
Two-way 6.5″ install loudspeaker in a moulded ABS cabinet, 80 Hz to 20 kHz, 90° × 60°, on a 70/100 V line or at 8 Ω.